Exactly How to Install a Bathtub
Exactly How to Install a Bathtub
Blog Article
The article author is making several good points relating to Tools You Need to Install a New Bathtub in general in this content on the next paragraphs.
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Mounting a tub isn't exactly brain surgery, but it does call for strong plumbing, carpentry, as well as in some cases, tiling abilities. Changing an old bathtub with a brand-new one is additionally a moderately challenging task. If the old tub is conveniently accessible, the job can move rapidly; if you need to open up a wall to eliminate the old bathtub and place the new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will require a helper to leave the old bathtub and set in the new one. See to it you have actually certified on your own for the job as well as are comfortable attempting it. Instead of hiring a service provider to take over a halfway-completed task, it is much better to consider utilizing one prior to you begin. Possibilities are you may need a professional plumber to make tube connections.
This write-up will assist you mount a new bath tub in your restroom if you have actually already gotten a new bathtub and also don't need to transform the arrangement of your previous water pipes.
Your devices as well as product checklist should make up the following:
Getting ready for the Installation
First of all, the sustaining framework provided with the bath needs to be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets unit to avoid pressure on the tub.
Fit the adaptable faucet connectors to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you make use of every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is separate the water system. After doing so, switch on the taps to drain any type of water staying in the system. The process of removing the existing taps can be quite problematic due to the limited accessibility that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a cloth ready for the remaining water that will come from the pipes. Once the supply pipes have been removed, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this process. When the taps have been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Before proceeding to fit the new faucets, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bathtub
Using both wood boards under its feet, put the tub in the required position. The wood boards are handy in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four tiny factors.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the tub until the level checks out level.
To mount faucets, fit the bottom of the furthest adaptable faucet connector to the appropriate supply pipeline by making a compression join; then do the very same for the various other tap.
Activate the water system and examine all joints as well as new pipework for leakages as well as tighten them if necessary. Load the tub and also examine the overflow electrical outlet and the regular outlet for leakages.
Lastly, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the bathtub must wait until the tub has been utilized at the very least once as this will certainly resolve it into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin making sure that the washing machines remain in place between the faucet and the sink. Secure the faucet in position with the manufacturer offered backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The former type must be attached to the faucet ends first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall between the bath and the tiling, resulting in problems with dampness and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components as well as fittings. They are sold in tubes and cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of drenched paper or soft rope. Keep in mind to always fill the bathtub with water prior to securing, to enable the motion experienced when the tub is in usage. The sealer can split relatively early if you do not take into account this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the marketplace. It is a good idea to fit the tiles using waterproof or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that piece on Tools You Need to Install a New Bathtub while perusing the search engines. Sharing is nice. You just don't know, you might be helping someone out. Many thanks for going through it.
Book An Appointment
Report this page